Sonic-alert Digital Program Controller DCP301 Uživatelský manuál Strana 148
- Strana / 187
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 9. TROUBLESHOOTING
9-6
■ PID set items cannot be displayed by repeatedly pressing in program setup
state
■ Items cannot be changed by pressing in program setup state
The pattern item has not been set.
Programming items are set to “display OFF”.
Cause Remedy
Set SP and time data.
All setup data
C 6 8 to C 7 1 settings are “1”. Set
necessary items to 0.
■ Event items cannot be displayed by repeatedly pressing in program setup
state
Event type is controller status event.
Programming items are set to “display OFF”.
Cause Remedy
Set event type (
E T 1, E T 2, E T 3) in event configura-
tion date to one of 0 to 11 or 50.
Set setup data
C 6 8 setting to 0.
■ Time events cannot be displayed by repeatedly pressing in program setup
state
Time event is assigned to segment No. event.
This model does not support time events.
Programming items are set to “display OFF”.
Cause Remedy
Change event configuration data
T T setting and assign
to time event.
Select a mode that supports time events (option).
Set setup data
C 6 q setting to 0.
PID set auto-switching is set to ON.
The controller is set to programmer function
by 5G output.
3-position control is selected by 3D output.
Programming items are set to “display OFF”.
Cause Remedy
Set setup data
C 1 1 setting to 0.
Set setup data
C 1 8 setting to 0.
Set setup data
C 4 5 setting in use to 0 and switch to
PID control from 3-position control.
Set setup data
C 7 0 setting to 0.
■ G.Soak items cannot be displayed by repeatedly pressing in program setup
state
Programming items are set to “display OFF”.
Cause Remedy
Set setup data
C 7 0 setting to 0.
■ PV start items, cycle items and pattern link items cannot be displayed by repeat-
edly pressing in program setup state
Programming items are set to “display OFF”.
Cause Remedy
Set setup data
C 7 1 setting to 0.
- Digital Program Controller 1
- User’s Manual 1
- WARRANTY 2
- TECHNICAL ASSISTANCE 2
- SAFETY PRECAUTIONS 3
- Unpacking 6
- Contents 8
- Chapter 7. PARAMETER SETUP 10
- Chapter 8. PROGRAM SETUP 10
- Chapter 9. TROUBLESHOOTING 11
- Chapter 10 12
- SPECIFICATIONS 12
- Chapter 11. CALIBRATION 12
- RUN/HOLD 13
- 1-1 Features 14
- 1-2 Basic Function Blocks 15
- 1-3 Data Structure 16
- 1-4 System Configuration 17
- 1-5 Model Numbers 18
- 2-1 Structure 19
- 2-2 Console 20
- Basic display state 22
- ■ Loader jack 25
- 2-3 Input Type and Range No 26
- Chapter 3. MOUNTING 28
- 3-2 Panel Cutout Dimensions 29
- 3-3 Mounting 30
- ■ Dust-proof cover 31
- ■ Mounting method 32
- 4-1 Wiring Precautions 33
- 4-2 Compensating Lead 35
- 4-3 Terminal Connections 36
- Direction 37
- ■ Power supply 38
- ■ Ground 38
- Chapter 4. WIRING 39
- ■ Connecting input 1 40
- ■ RS-485 interface 48
- Digital circuit 51
- 5-1 Data 52
- 5-2 Program Patterns 53
- ■ Events 1 to 3 54
- Chapter 5. FUNCTIONS 55
- ■ Time events 1 to 5 57
- ■ G.Soak (guarantee soak) 59
- ■ PID set selection 59
- (1)' 60
- (1)" 60
- ■ Pattern link 61
- 5-3 Modes 62
- ■ Mode transition 64
- ■ Mode transition operations 65
- ■ Mode transition limitations 66
- 5-4 Controller and Programmer 67
- ■ Control output 69
- ● 2G output 71
- ● 3D, 5K outputs 72
- MANUAL mode 72
- ■ SP output 73
- ■ Auxiliary output 73
- 6-1 Turning the Power ON 74
- Chapter 6. OPERATION 75
- Motor valve opening (%) 79
- Output state of events 1 to 3 79
- 6-3 Program Selection 80
- ■ Program selection 82
- ■ Read timing 83
- ■ Manual operation 84
- ■ Auto-tuning (AT) 84
- 7-1 Parameter Setup 86
- 7-2 How to Use 89
- 7-3 Parameter Setup List 92
- Handling Precautions 100
- E T 1 0 103
- E D 1 0 103
- H Y S 1 5 103
- D L 1 0 103
- PID Set No. Designated in the 108
- Program or Zone No. According 108
- ■ Setup data settings “S E t” 112
- SSR' 120
- q 0 (Special functions) 122
- Short-circuit 123
- ■ Table data settings “T B L” 125
- MV upper limit (CH1) 127
- I N S .” blinking 129
- d E L .” blinking 129
- C L R .” blinking 129
- ■ Programming map 131
- ■ Setting up pattern items 132
- ■ Display details 132
- Program No. Segment No 133
- ■ Setting up PV start items 138
- ■ Setting up cycle items 138
- P.L I N 139
- Program No 141
- Copy destination program No 141
- G .R E S 142
- ■ Alarm code display 144
- ■ Alarm categories 144
- 9-4 Replacing the Battery 152
- Comes out towards you 153
- Key cover 153
- Lock screw 153
- Connector 154
- RAM board 154
- (approx. 3cm x 8cm) 154
- Gray holder 155
- 10-1 Specifications 156
- Chapter 10. SPECIFICATIONS 157
- 25 ) and 157
- Item Specification 157
- ■ Accessories/option list 162
- 10-2 External Dimensions 163
- Chapter 11. CALIBRATION 166
- 4.0.4.4 169
- 2.0.2.2 169
- 11-2 Calibration Procedures 170
- ■Function test 171
- 1.0.1.1 174
- Table 11-11 175
- ■Current output calibration 176
- 11-3 Set Up 177
- Programming Map 179
- SAFETY REQUIREMENTS 180
- Revision History 184
- HONEYWELL SERVICE CENTERS 185
- No. CP-UM-5093E 187
Související produkty a manuály pro Hodiny Sonic-alert Digital Program Controller DCP301
Hodiny Sonic-alert SB200ss Uživatelský manuál
(2 stránky)
(2 stránky)
Hodiny Sonic-alert SBP100 Uživatelský manuál
(2 stránky)
(2 stránky)
Hodiny Sonic-alert SB300SS Uživatelský manuál
(2 stránky)
(2 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce